Applications

Applications

Home > Applications > Metal cutting > Cast Iron

Cast Iron

2024-10-08

Cast iron is one of the few materials where the cutting method decides the metallurgy of the finished part. Abrasive wheels and friction saws push heat into the workpiece; on grey iron that heat is mostly harmless, but on white or chilled iron it can provoke micro-cracking at the cut edge that only shows up after machining. Diamond wire removes material by grinding at low force with a narrow kerf, so the bulk of the part never sees a temperature rise.

Why cast iron behaves differently from steel

The free graphite in grey iron acts as a built-in lubricant, which is why it machines easily — and also why it cuts inconsistently on wire. The graphite flakes interrupt the chip, so the wire alternates between cutting metal and sliding through soft graphite. The practical effect is a cut that runs fast but leaves a slightly ragged edge on thin sections.

White cast iron and chilled surfaces are the opposite problem. They contain cementite rather than free graphite, and hardness commonly runs from 400 to 600 HB, with some chilled rolls and mill liners going higher. These are the grades where abrasive saws slow down badly and where diamond wire earns its cost.

Diamond wire versus the usual alternatives

  • Abrasive cut-off wheel — fast on small sections, but heat-affected zone and a wide kerf. Not practical above roughly 150 mm thickness.
  • Band saw — good on grey iron bar stock, struggles on chilled surfaces and on sections that work-harden.
  • Wire EDM — excellent accuracy, but limited by conductivity, part size and a much slower removal rate on thick sections.
  • Diamond wire — no thermal damage, narrow kerf, works on thick and irregular castings, and cuts chilled grades that defeat carbide tooling.

Selecting the wire for cast iron

WorkpieceWire diameterDiamond gritBond
Grey iron, section under 100 mm0.25–0.30 mm#80–#120Nickel-plated
Grey iron, heavy section0.35–0.45 mm#40–#60Nickel-plated
White / chilled iron0.30–0.40 mm#40–#80Nickel-plated, high density
Thin-wall castings, minimal kerf0.20–0.25 mm#120–#150Nickel-plated

Finer grit gives a cleaner edge but cuts slower and loads more easily in the graphite. On mixed batches, it is usually cheaper to run one coarse wire and accept a slightly rougher edge than to change spools between parts.

Starting parameters

On grey iron, wire speed typically sits in the 15–25 m/s band with a light feed; the wire should be cutting, not rubbing. On chilled iron, drop the speed and keep the tension steady rather than pushing the feed, because the failure mode there is diamond pull-out, not wire breakage. Use a water-based coolant with a rust inhibitor — cast iron will flash-rust on the cut face within hours if it is left wet.

These are starting points, not settings. Section thickness, casting skin and the amount of sand inclusion all shift the window, and the only reliable way to fix a parameter set is a test cut on your own material.

Send us a sample and we will cut it

We keep test results on grey, ductile, white and chilled iron, and we will tell you which wire we would run and what it should cost per square metre of cut. If a different process suits your part better, we will say so.

Test the cut before you commit to the machine

Send us a sample of your material. We return a cut-quality report with the wire specification and machine format that suit it — free of charge, no obligation.

ENSOLLTECH PTE. LTD. · Singapore (UEN 202551184N) · manufacturing in Zhengzhou, China · reply within one working day

Other materials we cut

  • Aluminium — plate, billet and extrusion; loading control, not abrasive wear
  • Polysilicon — chunk reduction, rod cropping and wafering; kerf is the cost
  • Optical glass — prisms, windows and freeform; shallow subsurface damage
  • Quartz stone — engineered and sintered slabs; chip-free visible edge

Not listed? Send a sample and we will cut it and tell you what wire to run.

Supplied by ENSOLLTECH PTE. LTD.

ENSOLLTECH PTE. LTD. is a Singapore company (UEN 202551184N), registered at 266A South Bridge Road, #02-01, Singapore 058815. We supply endless diamond wire loops and diamond wire saw machines; the products are manufactured at our group’s own ISO 9001-certified plant in Zhengzhou, China — not sourced from third-party traders.

Company profile: About ENSOLLTECH  ·  Technical enquiry: Contact our Singapore office

Send Message

If you have any question, please contact us

    Home Tel Mail Inquiry

    WhatsApp Us